Sign Up to our social questions and Answers Engine to ask questions, answer people’s questions, and connect with other people.
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
How To Enable Dhcp On Ethernet?
To enable DHCP on Ethernet, you need to go to your computer's Network Settings, choose the Ethernet connection, and then choose "Enable DHCP". This will assign an IP address, Subnet Mask, Default Gateway and DNS Servers to your computer, allowing it to connect to the network and access the internet.
To enable DHCP on Ethernet, you need to go to your computer‘s Network Settings, choose the Ethernet connection, and then choose “Enable DHCP“. This will assign an IP address, Subnet Mask, Default Gateway and DNS Servers to your computer, allowing it to connect to the network and access the internet.
See lessHow To Configure Intervlan Routing On Layer 3 Switches?
1. Connect the two Layer 3 switches together with a trunk link. 2. Configure the first switch with a VLAN interface (VIF) per VLAN you plan to route between. Assign an IP address to each VLAN interface. 3.Configure a trunking protocol such as 802.1Q on the trunk link connecting the two switches so tRead more
1. Connect the two Layer 3 switches together with a trunk link.
2. Configure the first switch with a VLAN interface (VIF) per VLAN you plan to route between. Assign an IP address to each VLAN interface.
3.Configure a trunking protocol such as 802.1Q on the trunk link connecting the two switches so that each VLAN is allowed to pass through.
4. Configure static routes on each switch pointing to the subnets associated with each VLAN.
5. Create an access list on each switch to control which traffic can pass through the trunk link.
6. Enable routing protocols like RIPv2 or OSPF if desired to facilitate dynamic routing.
7. Test with a ping utility to verify that hosts from one VLAN can reach hosts in another.
See lessHow To Redirect Ports From Router To Computer?
1. Log into your router's web-based setup page. To do this, open a browser and type in the IP address of your router. This will usually be something like 192.168.0.1 or 192.168.1.1. Refer to your router’s manual for the correct address. 2. Locate the port forwarding section of the router. This may aRead more
1. Log into your router‘s web–based setup page. To do this, open a browser and type in the IP address of your router. This will usually be something like 192.168.0.1 or 192.168.1.1. Refer to your router’s manual for the correct address.
2. Locate the port forwarding section of the router. This may also be called NAT, Virtual Servers, or Applications & Gaming.
3. Create a port forwarding entry. Enter the information required such as the port number, protocol, IP address, and more.
4. Save the changes and apply them. Restart the router if necessary.
5. Test to make sure the port is open by running a port scan from an external source.
See lessHow To Change Native Vlan On Cisco Switch?
1. Log into your Cisco switch using an SSH client or a direct console connection 2. Enter configuration mode by typing “configure terminal” then press Enter 3. Type “vlan native <VLAN_ID>” then press Enter 4. Verify the change with the command “show vlan native” 5. Exit configuration mode by tRead more
1. Log into your Cisco switch using an SSH client or a direct console connection
2. Enter configuration mode by typing “configure terminal” then press Enter
3. Type “vlan native <VLAN_ID>” then press Enter
4. Verify the change with the command “show vlan native”
5. Exit configuration mode by typing “end” then press Enter
6. Save the changes to the native VLAN by typing “copy running–config startup–config” then press Enter
See lessHow To Change Cisco Switch Password?
1. Log in to the switch by typing the privileged EXEC command “enable” at the prompt. 2. Enter the commands “configure terminal” and “enable secret” followed by the new password. 3. Type “exit” and hit enter to save the configuration. 4. Type “wr memory” to write the new password to NVRAM. 5. Log ouRead more
1. Log in to the switch by typing the privileged EXEC command “enable” at the prompt.
2. Enter the commands “configure terminal” and “enable secret” followed by the new password.
3. Type “exit” and hit enter to save the configuration.
4. Type “wr memory” to write the new password to NVRAM.
5. Log out from the switch by typing “exit” and reconnecting with the new password.
See lessWhere Does Routing Occur Within The Dod Tcp/Ip Reference Model?
Routing occurs at the Network layer (Layer 3) of the DoD TCP/IP Reference Model. At this layer, devices known as routers use IP addresses and routing protocols to determine the best path for data to travel across the network.
Routing occurs at the Network layer (Layer 3) of the DoD TCP/IP Reference Model. At this layer, devices known as routers use IP addresses and routing protocols to determine the best path for data to travel across the network.
See lessHow To Connect Router With Pc In Cisco Packet Tracer?
1. Open the Cisco Packet Tracer simulation software. 2. Select a router and a computer from the Network Devices Palette. 3. Drag the devices to the workspace. 4. Connect the Fast Ethernet (FE) port of the router to the FE interface of the computer. 5. Right-click on the router, then select "ConfigurRead more
1. Open the Cisco Packet Tracer simulation software.
2. Select a router and a computer from the Network Devices Palette.
3. Drag the devices to the workspace.
4. Connect the Fast Ethernet (FE) port of the router to the FE interface of the computer.
5. Right–click on the router, then select “Configure“.
6. Select “Network Setup”.
7. Enter a valid IP address, subnet mask, and default gateway for the router.
8. Click “OK”.
9. Right–click on the PC, then select “Configure”.
10. Select “Network Setup”.
11. Enter an IP address, subnet mask, and default gateway that match the router settings.
12. Click “OK”.
13. Right–click on the router and select “Start”.
14. Right–click on the PC and select “Start”.
15. The two devices should now be able to communicate with each other.
See lessWhich Of The Following Is Not One Of The Three Main Types Of Linux Commands??
Application Programming Interface (API) is not one of the three main types of Linux commands. The three main types are: command line, shell, and graphical user interface (GUI).
Application Programming Interface (API) is not one of the three main types of Linux commands. The three main types are: command line, shell, and graphical user interface (GUI).
See lessHow Is The Bandwidth Of a Network Measured?
Bandwidth is typically measured in bits per second (bps), and it measures the maximum data rate of a network connection. It's often used to measure the capacity of a network for transferring data packets, meaning how much data can be transmitted over a given amount of time. Other metrics used to meaRead more
Bandwidth is typically measured in bits per second (bps), and it measures the maximum data rate of a network connection. It‘s often used to measure the capacity of a network for transferring data packets, meaning how much data can be transmitted over a given amount of time. Other metrics used to measure network bandwidth include latency (the delay between when a packet is sent and received) and jitter (the variation in latency).
See lessWhich Statement Regarding The Border Gateway Protocol Bgp Is Accurate?
Border Gateway Protocol (BGP) is an exterior gateway protocol used to exchange routing and reachability information between two or more Autonomous Systems (ASes) on the Internet. BGP is the only protocol that is designed to be used for routing on the Internet, and it is the most popular inter-domainRead more
Border Gateway Protocol (BGP) is an exterior gateway protocol used to exchange routing and reachability information between two or more Autonomous Systems (ASes) on the Internet. BGP is the only protocol that is designed to be used for routing on the Internet, and it is the most popular inter–domain routing protocol today.
See less