Q & A
Share
Sign Up to our social questions and Answers Engine to ask questions, answer people’s questions, and connect with other people.
Lost your password? Please enter your email address. You will receive a link and will create a new password via email.
Please briefly explain why you feel this question should be reported.
Please briefly explain why you feel this answer should be reported.
Please briefly explain why you feel this user should be reported.
How To Make a Crossover Ethernet Cable?
1. Gather the necessary materials. You will need two Ethernet cables and a crimping tool. 2. Cut one of the Ethernet cables in half. 3. Strip the plastic insulation off each end of the cut Ethernet cable. 4. Separate the pairs of wires. 5. Line up the wires from each of the two Ethernet cables so thRead more
1. Gather the necessary materials. You will need two Ethernet cables and a crimping tool.
2. Cut one of the Ethernet cables in half.
3. Strip the plastic insulation off each end of the cut Ethernet cable.
4. Separate the pairs of wires.
5. Line up the wires from each of the two Ethernet cables so that the corresponding colored wires are matched up.
6. Twist the corresponding wires together.
7. Use the crimping tool to secure each pair of wires together.
8. Cover the connection with electrical tape or heat shrink tubing.
9. Connect the two cables together by plugging one end into each other.
10. Test the connection by plugging the cable into a computer and network device to ensure a proper connection.
See lessHow To View User Password In Linux?
It is not possible to view user passwords in Linux. However, you can reset a user's password if you have root access. To do this, open a terminal and type the command 'sudo passwd username', where username is the username of the user whose password you want to reset. You will then be prompted to entRead more
It is not possible to view user passwords in Linux. However, you can reset a user‘s password if you have root access. To do this, open a terminal and type the command ‘sudo passwd username‘, where username is the username of the user whose password you want to reset. You will then be prompted to enter and confirm the new password.
See lessHow To Check Free Ip Address In Network Through Cmd?
To check the free IP addresses on your network through the command prompt, open the command prompt and type "ipconfig /all". This will list all of the IP addresses currently in use on your network. Look for any IP addresses with a status of "available" to determine which IP addresses are free.
To check the free IP addresses on your network through the command prompt, open the command prompt and type “ipconfig /all“. This will list all of the IP addresses currently in use on your network. Look for any IP addresses with a status of “available“ to determine which IP addresses are free.
See lessHow To Change Ip Address On Vpn?
1. Open your VPN software. 2. Select the “Change IP” option from the list of settings. 3. Choose a new IP address from the list of available servers. 4. Click the “Connect” button to establish the connection. 5. Once the connection is established, the new IP address will be active.
1. Open your VPN software.
See less2. Select the “Change IP” option from the list of settings.
3. Choose a new IP address from the list of available servers.
4. Click the “Connect” button to establish the connection.
5. Once the connection is established, the new IP address will be active.
A Switch Is Associated With Which Osi Model Layer?
A switch is associated with the Data Link layer (Layer 2) of the OSI model.
A switch is associated with the Data Link layer (Layer 2) of the OSI model.
See lessWhat Is Ipsec And How Does It Work?
IPsec (Internet Protocol Security) is a protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session. It provides security for IP-based networks by authenticating the identity of connected devices and encrypting data toRead more
IPsec (Internet Protocol Security) is a protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session. It provides security for IP–based networks by authenticating the identity of connected devices and encrypting data to prevent interception and alteration of data. IPsec works by authenticating and encrypting each IP packet of a communication session. It uses the following protocols to provide a secure connection: Authentication Header (AH), Encapsulating Security Payload (ESP), Internet Key Exchange (IKE) and Internet Security Association and Key Management Protocol (ISAKMP). The AH and ESP protocols provide authentication and encryption of data, while IKE and ISAKMP are used to establish and manage the secure connection.
See lessIpv6 Was Introduced When Ipv4 Blank?
IPv6 was introduced in 1998, when IPv4 was running out of available IP addresses.
IPv6 was introduced in 1998, when IPv4 was running out of available IP addresses.
See lessWhich Of The Following Is a Private Ip Address?
A private IP address is an IP address that is reserved for private networks, such as those at home or in an office building. Examples of private IP addresses are 10.0.0.0 through 10.255.255.255, 172.16.0.0 through 172.31.255.255, and 192.168.0.0 through 192.168.255.255.
A private IP address is an IP address that is reserved for private networks, such as those at home or in an office building. Examples of private IP addresses are 10.0.0.0 through 10.255.255.255, 172.16.0.0 through 172.31.255.255, and 192.168.0.0 through 192.168.255.255.
See lessHow Do I Find Out What My Smtp Server Is?
The simplest way to find out what your SMTP server is is to contact your Internet service provider's (ISP) technical support team. They should be able to provide you with the necessary information. Additionally, you can also use an online SMTP lookup tool to find out your server settings.
The simplest way to find out what your SMTP server is is to contact your Internet service provider‘s (ISP) technical support team. They should be able to provide you with the necessary information. Additionally, you can also use an online SMTP lookup tool to find out your server settings.
See lessHow To Make a Static Ip?
1. Open your router's configuration page. Depending on your router, this may be done by entering a specific URL in your web browser's address bar or by using a program that came with your router, such as Linksys Connect or Netgear Genie. 2. Log into your router using the default username and passworRead more
1. Open your router’s configuration page. Depending on your router, this may be done by entering a specific URL in your web browser’s address bar or by using a program that came with your router, such as Linksys Connect or Netgear Genie.
2. Log into your router using the default username and password. If you have changed the username and/or password since setting up the router, use the new credentials instead.
3. Locate the Static IP Address settings. This section may be labeled as “Static DHCP,” “Static IP,” “Static Lease,” or something similar.
4. Enter the IP address you want to use for your device. Make sure the IP address is not already being used by another device on the network.
5. Enter the gateway IP address. This should be the same as your router’s IP address.
6. Enter the subnet mask. This is usually a 255.255.255.0 address.
7. Enter the DNS server address. This is usually the same as your router’s IP address.
8. Save the settings. Depending on your router, this may be done by clicking a Save or Apply button.
9. Assign the static IP address to your device. This is done by entering the static IP address into the device’s network settings.
See less